Baseball Pitches Chart: Types, Speeds & Movement

By Sarah Miller · February 4, 2051

All Baseball Pitches Chart: Types, Speeds, and Movement Patterns

Below is a comprehensive chart of all the different baseball pitches thrown in modern baseball, including fastball variants, breaking balls, and off-speed pitches, with data on average velocity, spin rate, movement profiles, and usage frequency among MLB pitchers. This guide breaks down each pitch type with expert analysis, helping players, coaches, and fans understand how each pitch works and why it's effective.

Types of Baseball Pitches: A Complete Breakdown

Major league pitchers use a diverse arsenal to outthink and overpower hitters. Each pitch exploits physics—velocity, spin axis, and seam orientation—to create unique movement patterns. Understanding these differences is key for both performance and analysis.

Four-Seam Fastball (4S)

Average Velocity: 92–97 mph
Spin Rate: 2,200–2,600 RPM
Movement: Minimal drop, slight 'rising' effect due to backspin
Purpose: Establish dominance, high in the zone

Sinker (Two-Seam Fastball, 2S)

Average Velocity: 90–95 mph
Spin Rate: 1,800–2,200 RPM
Movement: Arm-side run and sink
Purpose: Induce ground balls, especially against same-side batters

Changeup (CH)

Average Velocity: 80–88 mph
Spin Rate: 1,800–2,200 RPM
Movement: Slight arm-side fade and drop
Purpose: Disrupt timing with speed differential from fastball

Slider (SL)

Average Velocity: 83–89 mph
Spin Rate: 2,300–2,800 RPM
Movement: Sharp lateral break with some downward tilt
Purpose: Swing-and-miss pitch, especially effective vs. opposite-handed hitters

Curveball (CB)

Average Velocity: 75–82 mph
Spin Rate: 2,200–2,700 RPM
Movement: 12-to-6 vertical drop or slurve-like tilt
Purpose: Looper pitch to generate swings over the top

Cutter (FC)

Average Velocity: 88–93 mph
Spin Rate: 2,000–2,400 RPM
Movement: Late, sharp glove-side cut
Purpose: Jam hitters or break bats; popularized by Mariano Rivera

Forkball/Split-Finger Fastball (SF)

Average Velocity: 80–88 mph
Spin Rate: 1,200–1,800 RPM
Movement: Sharp downward dive
Purpose: Generate weak contact or swings and misses

Knuckleball (KN)

Average Velocity: 60–70 mph
Spin Rate: < 500 RPM
Movement: Erratic, unpredictable flutter
Purpose: Confuse hitters with lack of spin; rare but iconic

Pitch Type	Avg. Velocity (mph)	Spin Rate (RPM)	Horiz. Break (in)	Vert. Break (in)	Usage % (MLB Avg)
Four-Seam Fastball	94.1	2,380	-0.4	8.9	48.6%
Sinker	92.3	2,050	4.7	-8.2	14.2%
Changeup	85.6	2,010	5.1	-7.3	8.7%
Slider	86.4	2,540	2.8	-2.9	12.1%
Curveball	78.9	2,460	-1.2	-6.7	9.4%
Cutter	90.2	2,180	-2.1	2.4	7.0%
Splitter	84.3	1,520	3.9	-10.1	2.8%
Knuckleball	68.5	420	±3.0 (random)	±4.0 (random)	0.1%

Table data source:1, 2

Data shows that the four-seam fastball remains the most dominant pitch in MLB, used nearly half the time across all pitchers. Sliders have seen a significant rise in usage over the past decade due to their high swing-and-miss rates, while knuckleballs are nearly extinct at just 0.1% usage. Spin rate and movement metrics highlight how modern analytics shape pitch selection and development.

How Pitch Movement and Velocity Influence Effectiveness

The success of a pitch depends not just on speed, but on how it moves relative to expectations. Advanced tools like TrackMan and Rapsodo measure spin efficiency, release angle, and movement vectors to optimize performance.

Key Factors in Pitch Design

Velocity Differential: A changeup 10+ mph slower than a fastball disrupts hitter timing.
Spin Axis: Determines direction of movement—tilted spin creates sliders; pure backspin yields rising fastballs.
Release Point Consistency: Helps disguise pitches and prevent tipping.
Vertical Approach Angle: Steeper angles on fastballs increase perceived velocity.

Popular Pitch Combinations

Effective pitchers sequence pitches to exploit platoon advantages and location. Common pairings include:

Four-seamer up / Splitter down – creates 'tunneling' effect
Fastball in / Slider away – expands strike zone horizontally
Curveball slow loop / Heater high – disrupts rhythm

Common Questions About Baseball Pitches

What are the 7 main types of baseball pitches?

The seven primary pitch types are: Four-seam fastball, sinker, changeup, slider, curveball, cutter, and split-finger fastball. The knuckleball is a rare eighth type used by only a few pitchers historically.

Which pitch is the hardest to hit in baseball?

Statistically, the slider generates the highest swing-and-miss rate among non-fastballs, especially when thrown low and away. However, well-located fastballs high in the zone are also extremely difficult to square up due to perceived velocity.

Who invented the splitter and who made it famous?

The split-finger fastball was developed in Japan and popularized in MLB by Hall of Famer Bruce Sutter. It became a signature pitch for pitchers like Roger Clemens, Jack Morris, and more recently, Yu Darvish.

Why do pitchers throw a cutter instead of a slider?

A cutter maintains more velocity than a slider and has late, subtle movement ideal for jamming hitters or busting bats. It’s less stressful on the arm than a traditional slider and is often used in fastball counts for precision strikes.

How do spin rate and seam-shifted wake affect pitch movement?

High spin rates enhance movement through the Magnus effect, while seam-shifted wake (SSW) explains unexpected movement caused by asymmetric seam interaction with air. Modern pitch design focuses on optimizing both for maximum deception and break.